How to Start Your Sprinkler System for Spring

Welcome to the Take Charge of Your Home series from Direct Energy! Hiring a professional to perform household maintenance may offer convenience and peace of mind, but you can do many of these jobs yourself with no experience or special tools. And in the process, you’ll save money, learn about how your home works and gain a sense of accomplishment from a DIY task done well!

How to Start Your Sprinkler System for Spring | Direct Energy Blog

For lawn and garden enthusiasts, spring is the most wonderful time of the year. It’s the season when flowers, trees and grass come alive with color — so long as they get the sunshine and water they need to thrive.

Dewinterizing Your Sprinkler System

When Mother Nature can’t hold up her end of the bargain, lawns and gardens need a little help from us humans. A garden hose or watering can will suffice, but homeowners with underground sprinkler systems know that the most convenient way to keep a healthy lawn is to automate the process.

That’s not to say that using a sprinkler system is a completely effortless process. In fact, shutting down the system for winter and reopening it in the spring are two fairly big jobs. But if you do them well, your only worry in between should be avoiding the sprinkler heads with the lawn mower.

Dewinterizing and starting your sprinkler system for the spring may take two hours or more, depending on the size of your property, the number of sprinkler heads and the condition of the system.

How to Start Your Sprinkler System for Spring | Direct Energy Blog

1. Check Your Lawn for Frozen Ground

Before you take the first step toward dewinterizing, you need to make sure your lawn agrees that winter is over. Use a shovel to dig at least one foot into the soil in an inconspicuous part of your lawn. If you strike frozen ground, you’re too early and should wait a week or two before conducting another dig test.

Starting your sprinkler system while the ground is still frozen can result in broken water lines during the startup process or even hours later, if the ground is cold enough to freeze the water in the lines. If your watering just can’t wait, you’ll want to hook up the hose and do it the old-fashioned way while the soil thaws.

2. Turn on Your Control Panel

Dewinterization starts at your sprinkler system’s brain — the main irrigation control panel. These are often installed outdoors, so you’ll probably need to wipe away a layer of dirt and clear out some cobwebs.

Turn on the control panel and review the current settings for time, date and irrigation zones. If your system has a battery backup and the batteries are more than six months old, this is a good time to replace them. All control panel models are a little different, so if you don’t have your system’s original documentation, find a copy online by searching for your panel’s model number.

3. Clean Your Sprinkler Heads

One of the most time-consuming steps is the inspection and cleaning of every sprinkler head and valve. The bigger your lawn is, the more time this will take.

Complete these steps at each sprinkler head:

  • Inspect the sprinkler head assembly for damage. If the nozzle is damaged, unscrew it from the head and buy a replacement at your local lawn care center. If there’s more extensive damage to the entire head assembly, the repair can be a bigger project that you might want to outsource to an irrigation maintenance professional.
  • Clean the nozzles thoroughly. An old toothbrush helps with this job. Any obstruction will affect the spray pattern, and that could result in some areas getting too little water while others get too much.
  • Make sure the sprinkler valve is closed, unless it’s the valve farthest from the main water source. You’ll want to leave this valve open and remove the sprinkler nozzle to allow air to escape when you turn on the water. If your system has multiple branches feeding off a main line, you should open the valve and remove the nozzle of the last sprinkler on each branch line.

How to Start Your Sprinkler System for Spring | Direct Energy Blog

4. Slowly Open the Main Valve

The next step is to open the main water valve, and this is where rookies can make an expensive mistake. Opening the valve too quickly sends a rush of water and air through the system, creating an effect called a “water hammer”. This surge of pressure can crack pipes, break valves and even send sprinkler heads rocketing into the air.

Slowly open the main valve until you can hear the water begin to flow, then wait for several minutes as water feeds into the main line. When you’re ready to continue, open the valve just a few degrees wider every couple of minutes until it’s fully open.

In a system where branch lines feed off the main line, there may be an additional valve where each branch line meets the main line. After completely filling the main line, you’ll need to repeat this slow-and-steady process at each branch line’s main valve.

Once all these valves are open, it’s time to check the faraway sprinkler valves that you left open earlier. With the sprinkler heads removed, any dirt and debris trapped in the line should be flushing out. As soon as the water flowing out looks clear, close the valve and screw the nozzle back into place.

5. Check Your Irrigation Zones

Your sprinkler system is now primed for its first watering of spring. And if you didn’t make any major changes to your system or landscaping since last year, you might not need to make any adjustments to your sprinkler nozzles. But it’s still worthwhile to test the irrigation of each of your zones, one at a time, to verify that your spray patterns are getting water where you need it.

Use your control panel to start the irrigation program for a single zone, then go watch your sprinklers at work. If you have any malfunctioning sprinkler heads, this is when you’ll notice them. And if your sprinklers have unusually low pressure, that’s often a sign of a water line break. You should watch for soggy spots to develop in your soil to pinpoint the area of the break, then shut down the water at the main valve until you can get it repaired.

If any nozzles need adjusting, take note of all the changes you want to make in the zone before turning off the sprinklers. You can only make the adjustments while the sprinklers are off, so this will spare you additional trips back and forth.

There are markings on top of each nozzle that indicate their spray patterns. To adjust a nozzle, unscrew the ring that holds it in place, lift it out of the head assembly and reinsert it with the markings pointing in the desired direction. Screw the ring back on and you’re good to go.

After working through each zone individually, activate your full irrigation program for one final walk-through inspection. If you like what you see, you’re all done until it’s time for winterization!

About 

Josh Crank is a freelance writer and content marketer with a background in legal journalism, travel writing, and marketing for numerous commercial industries. He's found his perfect fit at Direct Energy in writing about home maintenance and repairs, energy efficiency, and smart home technology. Josh lives with his wife, toddler son and endlessly howling beagle-basset hound mix in New Orleans.